MAX712電池充電器,max712 battery charger
關鍵字:MAX712電池充電器
本文源自下面的連接:http://www.rason.org/Projects/gelcell/gelcell.htm
12 VOLT GEL CELL CHARGER
BY N1HFX
Recently, a fellow amateur was looking for a gel cell charger which would first charge at a fixed rate and then later switch to a trickle charge when the cell was fully charged. After reviewing several catalogs and web sites, the MAX712 IC was discovered. This IC meets all the requirements for almost any type of battery charging system. The circuit in Figure 1 was designed specifically for 12 volt gel cells.
When a discharged gel cell is connected, the charger goes into a fast charge mode at a fixed rate of 400 ma. After the chip detects the voltage leveling off or when 4 1/2 hours has elapsed. (which ever happens first.) the fast charge will stop. After the fast charge has ended, the IC goes into a trickle charge rate of about 50 ma. This trickle charge continues until 13.8 volts is reached which will stop all charging current since the cell is now fully charged. If the cell voltage should drop for any reason, either a fast charge or trickle charge (IC will detect what is needed) will start again.
When constructing this circuit, be sure to attach a small heat sink to Q1. Apply a DC (partially filtered) voltage of at least 15.3 volts. The voltage must never go below this level even under load conditions. Many of the DC wall transformers available will work just fine as long as they meet the minimum voltage requirement. The input voltage can be as high as 24 volts. If the input voltage must be in the 30 volt range, increase R1 to about 820 ohms.
The output voltage must be aligned prior to use. Disconnect the battery from the circuit and apply power. Connect a digital volt meter or other accurate volt meter to pin 2 (positive lead) and to pin 12 (negative lead). Adjust R7 until exactly 13.8 volts is read.
Because this circuit will not overcharge a gel cell, the battery can be connected indefinitely. This circuit is designed primarily as a 12 backup system and can be connected to the load provided the device to be powered only draws current during power line interruptions. Use a diode from the battery to load if needed. This circuit makes an excellent battery backup to an amateur transceiver.
The MAX712 IC and the .62 ohm resistor are available from Digi-Key, 701 Brooks Ave, Thief River Falls, MN 56701 (1-800-344-4539). Order part numbers MAX712CPE-ND and 0.62W-1-ND respectively. All other parts are available at Radio Shack.
DE N1HFX
元件清單 PARTS LIST
C1
聲明:本文內容及配圖由入駐作者撰寫或者入駐合作網站授權轉載。文章觀點僅代表作者本人,不代表電子發燒友網立場。文章及其配圖僅供工程師學習之用,如有內容侵權或者其他違規問題,請聯系本站處理。
舉報投訴
發布評論請先 登錄 相關推薦 使用智能電池充電器估計充電狀態應用說明電子發燒友網站提供《使用智能電池充電器估計充電狀態應用說明.pdf》資料免費下載
發表于 09-13 10:47
?0次下載
如何選擇適合工業電池的充電器?如何選擇適合工業電池的充電器?我們應該使用微處理器控制的充電器還是獨立充電器? 選擇適合工業電池的充電器
鋰電池充電器和鉛酸充電器通用嗎鋰電池充電器和鉛酸充電器是兩種不同類型的充電器,它們的工作原理和特性不同,因此不能通用。下面將從三個方面詳盡、詳實、細致地介紹鋰電池
AD712介紹我最喜歡的ADI放大器AD712是一款雙通道、高速、精密、單芯片運算放大器,具有極高的性價比。我是玩音響的,也就是玩HIFI的,我用這顆運放作為整個HIFI功放的輸入前端,也就是前級。運放對選型
發表于 11-23 08:09
氮化鎵充電器傷電池嗎?氮化鎵充電器怎么選?氮化鎵充電器傷電池嗎?氮化鎵充電器怎么選? 氮化鎵(GaN)充電器被廣泛認為是下一代充電器技術的關鍵。與傳統
|
評論