• AD5684
• AD5684R
• AD5685R
• AD5686
• AD5686R

• EVAL-AD5684RSDZ
• EVAL-AD5686RSDZ

• CN0229

The AD5684/AD5686, members of the nanoDAC+? family are low power, quad, 12/16-bit buffered voltage output DACs. The devices include a gain select pin giving a full-scale output of 0V to VREF (gain = 1) or 0V to 2VREF (gain = 2).

The AD5684R/AD5685R/AD5686R nanoDAC+TM are quad, 12/14/16-bit, rail-to-rail, voltage output DACs. The devices include a 2.5V, 2ppm/?C internal reference (enabled by default) and a gain select pin giving a full-scale output of 2.5V (gain=1) or 5V (gain=2).

These devices operate from a single 2.7 V to 5.5 V supply, are guaranteed monotonic by design and exhibit less than 0.1% FSR gain error and 1.5mV offset error performance. The devices are available in a 3mm X 3mm LFCSP and a TSSOP package.

The AD5684/AD5686/AD5684R/AD5685R/AD5686R also incorporate a power-on reset circuit and a RSTSEL pin that ensures that the DAC outputs power up to zero scale or midscale and remain at that level until a valid write takes place. Each part contains a per-channel power-down feature that reduces the current consumption of the device to 4 μA at 3 V while in power-down mode. The devices employ a versatile SPI interface that operates at clock rates up to 50 MHz, and all devices contain a VLOGIC pin intended for 1.8 V/3 V/5 V logic.

The goal of this project (Microcontroller No-OS) is to be able to provide reference projects for lower end processors, which can't run Linux, or aren't running a specific operating system, to help those customers using microcontrollers with ADI parts. Here you can find a generic driver which can be used as a base for any microcontroller platform and also specific drivers for Renesas platforms.

HW Platform(s):

• Renesas Demo Kit for RL78G13 (Renesas)

The driver contains two parts:

• The driver for the AD5684R part, which may be used, without modifications, with any microcontroller.
• The Communication Driver, where the specific communication functions for the desired type of processor and communication protocol have to be implemented. This driver implements the communication with the device and hides the actual details of the communication protocol to the ADI driver.

The Communication Driver has a standard interface, so the AD5684R driver can be used exactly as it is provided.

There are three functions which are called by the AD5684R driver:

• SPI_Init() – initializes the communication peripheral.
• SPI_Write() – writes data to the device.
• SPI_Read() – reads data from the device.

The following functions are implemented in this version of AD5684R driver:

This section contains a description of the steps required to run the AD5684R demonstration project on a Renesas RL78G13 platform.

• Renesas Demo Kit for RL78G13 (Renesas)
• EVAL-AD5684RSDZ (ADI)

• IAR Embedded Workbench for Renesas RL78 Kickstart

An EVAL-AD5684RSDZ has to be interfaced with the Renesas Demonstration Kit (RDK) for RL78G13:

  EVAL-AD5684RSDZ Pin SYNC2  →  YRDKRL78G13 J11 connector Pin 1
  EVAL-AD5684RSDZ Pin DIN    →  YRDKRL78G13 J11 connector Pin 2
  EVAL-AD5684RSDZ Pin DOUT   →  YRDKRL78G13 J11 connector Pin 3
  EVAL-AD5684RSDZ Pin SCLK   →  YRDKRL78G13 J11 connector Pin 4
  EVAL-AD5684RSDZ Pin GND    →  YRDKRL78G13 J11 connector Pin 5
  EVAL-AD5684RSDZ Pin LDAC   →  YRDKRL78G13 J11 connector Pin 9
  EVAL-AD5684RSDZ Pin RESET  →  YRDKRL78G13 J11 connector Pin 10
  

The reference project:

• sets the output voltage of channel A and the reads back the raw value written into the DAC register;
• sets the output voltage of channel B using AD568X_SetVoltage() function;
• generates a sine wave on channel C;
• generates a trapezoid wave on channel D.